Store Hours:
7:30am - 5:00pm M-F
8:00am - 12:00pm Saturday
Cincinnati
(513) 489-9111
6130 Cornell Rd
Cincinnati, OH 45242
Norwood
(513)651-9111
4686 Paddock Rd
Cincinnati, OH 45229
Columbus
(614)224-9111
831 Harmon Ave
Columbus, OH 43223
Erlanger
(859)341-9111
2930 Crescent Springs Rd
Erlanger, KY 41018
Lexington
(859)254-9111
970 West New Circle Rd
Lexington, KY 40511
Dayton
(937)866-9111
801 E 1st St
Dayton, OH 45402
PRODUCTS
MANUFACTURERS
BACK TO JANELL.COM
BROWSE CATEGORIES
> Bolt
> Nail
> Nut
> Screws
> Staple
> Washer
Abrasives
Adhesives | Sealants | Tape
Concrete and Asphalt Chemicals
Concrete and Asphalt Products
Concrete Forming
Construction Fabrics
Decorative Concrete
Drill Bits and Drilling Accessories
Equipment
Erosion Control | SWPPP
Fasteners | Anchors
Fastening Pins & Inserts
Hand Tools
Hardscapes
Industrial Pumps
Leveling | Measuring | Surveying
Lumber Products
Masonry
Material Handling | Storage | Containment
Outdoor Products
Power Tool Accessories
Power Tools
Presses & Shop Equipment
Rebar and Wire Mesh
Safety Equipment and Products
Shop Vacuums
Structural Hardware
Tiles and Detectable Warning Pads
Tilt Up
Tool Storage | Job Site Boxes | Truck Boxes | Transfer Tanks
Trench Drains
Waterproofing Products
Home
/
Categories
/
Masonry
/
Anchoring Systems
/
Search:
Drill Bolt Brick Veneer Shear Anchoring System
358
Heckmann Building Products Inc
(click image to enlarge)
Quick Overview
Drill Bolts™ are 1/2” thick (12.7mm) in diameter and 6.25" in length. U-Clip is 14 gage. Drill Bolt™ and U-Clip™ are Hotdip Galvanized after fabrication in compliance with ASTM A153 requirement of 1.5 oz/ft2/side (CSA CAN-A370-04 requirement of 460g/m2/side) of zinc coating.
Complies Fully with US Building Codes:
Drill Bolt is attached to the stud side; the connecting screws are stressed shear.
Load resistance exceeds the requirements of CSA A370 and ACI 530 .
The total mechanical free play in the system does not exceed 1.2 mm, as required by CSA A-370.
The total sum of displacement under a load of 0.45 KN and mechanical free play in the system does not exceed 2.0 mm, as required by CSA A-370.
All parts are hot dip galvanized after fabrication per ASTM A-153, to comply with level 2 corrosion protection requirements as defined in CSA A-370.
Rigid Insulation Integrity Remains Uniterrupted:
The Drill Bolt creates a very tight penetration without disturbing adjacent sheeting and insulation.
U-Clip adjusts rotationally from outside to seal the penetration and positively retain the insulation in place.
U-Clip slot can be installed up or down to allow total vertical adjustment of 2 ¾” (70 mm).
Quick and Easy Installation:
The Drill Bolt™ installs with a power drill; the cutting point will penetrate through the sheeting and insulation from inside.
The Drill Bolt™ is equipped with a hex head matching the screw hex head so that only one tool is used.
The Drill Bolt™ is notched to indicate the depth of insertion required.
Interested in this item or want more information?
Call Mon. - Fri. 7:30 AM - 5:00 PM / Sat. 8:00 PM - 12:00 PM
Phone: (888) 489-9111
Email:
info@janell.com
Can't find what you want? Give us a call and we can help you find it.
Additional Information
Manufacturer: Heckmann Building Products Inc
© 2013- Janell Concrete and Masonry Equipment, Inc. | All Rights Reserved
Powered by 48ws.com